An independent reference about tanks, barrels and water storage at a country house. It does not sell equipment, gives no medical advice and is not connected with the former site on this domain.

Guides

Practical guides

The first article in this section answers the question everyone asks when putting a barrel under a downpipe: how much water will get into it after rain, and will it overflow in the very first downpour? For an estimate, all you need is a tape measure, a calculator and one simple rule about millimetres of rain.

A millimetre of rain on a square metre is a litre of water. Remember that rule and the roof of any shed becomes a simple multiplication problem.

— Side note

What you'll need

  • A tape measure and, if possible, a helper to measure the house or shed around the outside.
  • A sheet of paper for a sketch of the roof: which slopes there are and which downpipe each one drains into.
  • A calculator — the one on your phone will do.
  • Rainfall figures in millimetres: they are given in weather forecasts and weather service summaries.
  • The volume of your barrel or tank in litres — it is usually marked on the container itself or in its description.
  1. Find the slopes that drain into the barrel

    Look at where the water runs off each roof slope. Only what collects in the downpipe above the barrel will reach it. If the house has two slopes and two downpipes, count them separately.

    Illustrative example: the shed has a single-pitch roof and all the water goes into one downpipe.

  2. Measure the roof on plan

    For the estimate you need not the area of the slope itself but the area the roof covers seen from above — as if you were looking down on it. Rain falls roughly vertically, so the pitch hardly changes the amount of water collected. Measure the length and width of the building at the eaves.

    Illustrative example: at the eaves the shed is 6 m long and 5 m wide.

  3. Work out the area

    Multiply the length by the width. If the roof has a complex shape, split it into rectangles and add up their areas.

    Illustrative example: 6 × 5 = 30 m².

  4. Find the rainfall

    Rainfall is measured in millimetres: it is the depth water would reach on a flat surface if none of it ran off or evaporated. Take the figure for a single shower or for a month, depending on what you want to know.

    Illustrative example: 10 mm of rain fell in one shower.

  5. Convert to litres

    A depth of 1 millimetre on 1 square metre gives 1 litre of water. So multiply the area in square metres by the rainfall in millimetres to get litres — before losses.

    Illustrative example: 30 × 10 = 300 litres.

  6. Allow for losses

    Less than the calculated amount reaches the barrel: some water splashes off, some stays on the roof and in the gutters, some evaporates in warm weather, and you will divert the first dirty flush yourself. So the figure you get is an upper limit, not a promise.

    Illustratively: noticeably less than 300 litres will reach the barrel, and only watching your own roof will show the exact share.

  7. Compare with the barrel volume

    If the estimate is larger than the container, the excess water will leave through the overflow. That is normal, but the overflow must lead somewhere safe. If heavy rain is common where you live, consider a second barrel linked to the first.

    Illustrative example: a 200-litre barrel will fill before the rain stops, and about 100 litres will go to the overflow.

  8. Note it down and check in practice

    Mark the water level on the barrel before and after the next rain and compare it with your estimate. After a couple of observations you will know how efficient your roof and downpipe are and can plan your watering more accurately.

Common mistakes

  • Measuring the length of the slope instead of the roof area on plan, and getting an overestimate.
  • Counting the whole roof when only one slope drains into the barrel.
  • Mixing up centimetres and millimetres of rain and being out by a factor of ten.
  • Treating the figure before losses as the exact amount of water in the barrel.
  • Forgetting the overflow and being surprised by a puddle at the foundations after a downpour.
  • Installing a barrel without a screen and scooping leaves out of it a month later.

If something doesn't fit

  • If the roof has a complex shape, split it into rectangles on plan, find the area of each and add them up.
  • If there are no rainfall figures, put a level container with straight sides in an open spot and measure the depth of water with a ruler after rain.
  • If one barrel is not enough, link two containers with a connector near the bottom or put a second one under a neighbouring downpipe.
  • If there is no room by the house, collect water from the roof of a shed or carport: the calculation is exactly the same.

Check yourself

  • Slopes that drain into the barrel identified
  • Roof measured on plan, not along the slope
  • Area worked out in square metres
  • Rainfall taken in millimetres
  • Litres found by multiplying area by rainfall
  • Allowance made for losses
  • Estimate compared with the barrel volume
  • Overflow directed away from the foundations

Catalogue of English-language articles

This catalogue will gradually fill with standalone practical articles written for English-speaking readers about keeping water on hand at home: water butts and rain barrels, garden watering, looking after stored water and getting ready for winter. Every article has its examples and wording checked before publication.

What we're working on

  • Choosing a spot for a water butt or rain barrel: shade, slope, access and distance from the house.
  • Linking two rain barrels so that water flows from one into the other.
  • Diverting a downpipe into a barrel and back again when the barrel is full.
  • Watering beds, a greenhouse or containers from a barrel with a can or a hose.
  • Getting a garden water tank and an outdoor tap through a hard frost.

How we publish

  • Articles in this catalogue are written separately for each language version and are not translations.
  • Some articles link to third-party websites, including gaming services; we do not control their content, prices or terms.
  • We do not sell equipment or publish advertising for shops or services, rankings, prices or reviews.
  • Reference

    Litres and cubic metres, the volume of a barrel and a rectangular tank, rainwater estimates and properties of water.

  • Questions

    Short answers on choosing a tank, collecting rainwater, watering, green water, mosquitoes and winterising.

  • Sections

    Seven sections: containers, rainwater, watering, summer shower, cleaning and green water, winterising, safety.

Sources

  • International System of Units (SI): unit definitions
  • Editorial material of the guide

Information is current as of the date the page was prepared. Only unit conversions taken from their definitions and the general properties of water are exact here; tank sizes, roof areas and rainfall amounts in the examples are illustrative, so plug in your own measurements and do the sums yourself.